Perma-Chink Colors
Product Information
Perma-Chink is a flexible, textured log home chinking that seals the open gaps between logs to eliminate heat loss and air infiltration. Even though it looks and feels like traditional mortar, it’s not. Perma-Chink is a pure acrylic that adheres to logs and stretches to maintain a tight seal by following log movement.
Features
- Eliminates Air and Water Infiltration
- Remains Flexible to Allow for Log Movement
- For Exterior and Interior
- Suitable for all Climates
Application Temperature
40° to 90°F
Application Methods
Chink Pump
Bulk-loading gun and follow plate
Ratchet caulking gun
Application bag
Surface Preparation
Clean and dry
Free of oils and wax
Backing material or bond breaker
Shelf Life
3 Years
Frequency
One-time application
Special Instructions
Apply to approximately 3/8″ thickness
Avoid application in direct sunlight
Chink seam size should be 1/6 of log diameter
Drying Time
Skins over in 1-2 hours
Cure in 2-8 weeks depending on temperature and humidity
No matter what size your project, we have multiple sizes to meet your needs.
5 gallon pails are best suited for large projects, paired with a follow plate and bulk loading gun (manual or powered). This combination is less expensive than using tubes.
Perma-Chink Chinking and Sealant Calculator
What happens if I go less width than what the manufacturer recommends?
Not all logs on your home move at the same rate, some may move a lot and others barely anything. When they make the recommendation they figure out the most movement you would see out of two logs touching each other and recommend a joint size that will allow the stretch to happen without failure. Some people want the joint to be smaller due to cost or the look. If you took a 1.5" recommendation and went with 1" instead, you will notice a few more repairs over the years if you get two logs that really move. You are not likely to see failure everywhere if you were deep enough with the joint in the first place ( notice we are talking depth here...not the initial joint width question)
The smaller you make the width the more likely you will see failures or separation. In our experience we have seen good results if people use 2/3 of the recommendation...but we don't recommend pushing it further than that.
Not all logs on your home move at the same rate; some may move a lot and others barely at all. When they make the recommendation they figure out the most movement you would see out of two logs touching each other factoring in the size of the logs. They recommend a joint size that will allow the stretch to happen without failure. The sealants and chink are designed to strech 2.5x the joint size before failing. Big logs overall move more so require a bigger joint. If you short it too much there may not be enough material to handle the log movement.
Some people want the joint to be smaller due to cost or the look.
For Example: If you took a 1.5" recommendation and went with 1" instead, you will notice a few more repairs over the years if you get two logs that really move. You are not likely to see failure everywhere if you were deep enough with the joint in the first place ( notice we are talking depth here...not the initial joint width question)
The smaller you make the width the more likely you will see failures or separation. In our experience we have seen good results if people use at least 2/3 of the recommended joint size...but we don't recommend pushing it further than that.
Joint Width
Most manufacturers recommend 15% of the log diameter for joint size after the first drying season and up to 20% if it's in the first drying season.
Example: 10" log diameter x 15% = 1.5" recommended joint size
Want to go less? You can, but learn more if that is a good decision for you.
Lineal Footage
Take each wall and multiply by the number of rows of sealant high.
Example 40' long wall x 9 rows high= 360 lf . Then add your lineal footage from each wall together.
For corners add 30% to your height measurement.
For gable ends, count your rows and estimate each for length, then add together.
Joint Depth
Log Sealants are designed to stretch as your logs move. They need an appropriate width as above, but even more important they require enough depth (material) so as not to fail.
Recommended Depth:
Joint Width 1/2" or less= 1/4" depth
Joint Width 5/8" or greater= 3/8" depth up to 1/2" Learn More about playing with depth
*Note: Quantities are based on the provided measurements. Actual product required can vary based on real life thickness used and contours of the logs. All calculations based on the use of backer rod
Perma-Chink Chinking
REQUEST FREE SAMPLES (click here)
Sealant Calculator & More Info
Energy Seal Textured Log Caulking
REQUEST FREE SAMPLES (click here)
Caulking Calculator & More Info
Reviews
There are no reviews yet.